Cuttlebug Sandwich Stack Rules!

Special Thanks to posters on the Splitcoast Stampers boards for all their input into this compilation
www.splitcoaststampers.com

Cuttlebug Sandwich Stack Rules!
Important Sandwiching Notes:
Cuttlebugs differ from machine to machine, and the space between the rollers can vary, so be SURE to ALWAYS err on the THIN side; you can pass the sandwich through the machine again, but if you start out too thick, you can potentially break a plate or otherwise hurt your new ‘bug!
If a cardstock or chipboard shim is noted, always try the sandwich without first, then add cut-to-size (the size of the plates) cardstock or chipboard layers until the appropriate thickness of the sandwich is determined.

Cardstock
Chipboard
Magnetic/ Metal Sheets & Thin cork (Media)
Cuttlebug Dies
Plate "A", Plate "B", Die (cutting side up), Cardstock, Plate "B"
Plate "A", Plate "B", Die (cutting side up), Chipboard, Plate "B"
Plate "A", Plate "B", die (cutting side up), Media, Plate "B"
Cuttlebug Embossing Folders
Plate "A", Plate "B", Folder (with cardstock inside), Plate "B"
Plate "A", Plate "B", Folder (with chipboard inside), Plate "B"
Plate "A", Plate "B", Folder (with metal sheet inside), Plate "B"
Big Impressions Texture Plates
Plate "A", BI texture Plate, Cardstock, Silicone Rubber pad (from BISK), Impressions Pad (from BISK)
*BISK-Big Impressions Starter Kit


BigShot Embossing Folders
Plate "A", Plate "B", Folder (with cardstock inside), Plate "B", Cardstock shim


BigShot Large Dies
Plate "B", Cardstock, Die (cutting side down), Plate "B"


Brass Embossing Stencils
Plate "A", Plate "B", mouse pad (cut to size, rubber side up), Cardstock, Brass stencil, Plate "B"
Sandwich may need to pass through several times based on cardstock thickness


Fiskars Texture Plates
Plate "A", Fiskars texture Plate, Cardstock, tan Wizard pad, black or tan Wizard pad, (possible Cardstock shim,) Plate "B"
Also try:
Plate "A", Fiskars texture Plate, Cardstock (lightly misted with water), 2 layers Fun Foam, Chipboard Shim, Plate "C"
Also try:
Plate "A", Fiskars texture Plate, Cardstock (right side towards TP), Rubber Plate (made from Plumber’s rubber gasket), Plate "C"


QuicKuts Dies (Grand)
Plate "A", Plate "B", Die, Cardstock, Plate "C"


QuicKuts Dies (Regular)
Plate "A", Plate "B", Die, Cardstock, Plate "C"
Plate "A", Plate "C", Die (cutting side up), Chipboard, Cardstock shim, Plate "B"

Revolution Dies
Plate "A", Plate "C", Die, Cardstock, Plate "B"


Sizzix CutNFold Dies
Plate "A", Die, Cardstock, Plate "B", Chipboard shim
Also try:
Plate "B", Cardstock, Die, Chipboard shim (maybe 6 layers)


Sizzix Embossing Folders
aka Simple Impressions
Plate "A", Plate "B", Folder (with cardstock inside), Plate "B"
Also try:
Plate "A", Chipboard shims, Folder (with cardstock inside), Plate "B"


Sizzix Original Dies & other Steel Rule Dies
Plate "B", Cardstock, Die (cutting side down), Plate "B"
Plate "B", Chipboard, Die (cutting side down), Plate "B"

Sizzlit Dies
Plate "A", Plate "B", Die (cutting side up), Cardstock, Plate "B"
Note: Provocraft suggests using Place" C" instead of the second Plate "B", however, CB owners have cracked plates, so try with two "B" plates first.


Wizard Spellbinders Dies (to cut)
Plate "A", Plate "C", Die, Cardstock, Plate "B"


Wizard Spellbinders Dies (to emboss)
Plate "A", Plate "B", Die, Cardstock, Tan Wizard pad, Plate "B"







Special Thanks to posters on the Splitcoast Stampers boards for all their input into this compilation
www.splitcoaststampers.com